[plamo:28122] Re: libata installer

[Takehiko Ogata]

尾形です。

IDEslaveのhddにdvdをonbordSATAにHDDとIDEcardにHDDをセット
してあるので順番としては
IDE(sr0) -> onbord SATA(sda,sdb) -> IDEcard(sdc)
になったようです。
以前のはこのM/Bでのテストではありませんがsata_silと
pdc202xx_newやsata_promiseのload順を変えることで順番の
調整が出来たように思います。このlibataにまとめられたものの場合
変更したい時にはudevの段階で調整することになるのだろうか。
lib/modulesをまだ見ていないのであれですが。

以下dmesgのhead -70
q 15
scsi0 : ata_piix
scsi1 : ata_piix
ATA: abnormal status 0x7F on port 0x177
ATA: abnormal status 0x7F on port 0x177
ata2.01: ATAPI, max UDMA/33
ata2.01: configured for UDMA/33
scsi 1:0:1:0: CD-ROM _NEC DVD_RW ND-2500A 1.06 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 32x/32x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:1:0: Attached scsi CD-ROM sr0
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata3: SATA max UDMA/133 cmd 0xEC00 ctl 0xE802 bmdma 0xDC00 irq 16
ata4: SATA max UDMA/133 cmd 0xE400 ctl 0xE002 bmdma 0xDC08 irq 16
scsi2 : ata_piix
ata3.00: ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata3.00: ata3: dev 0 multi count 16
ata3.00: applying bridge limits
ata3.00: configured for UDMA/100
scsi3 : ata_piix
ata4.00: ATA-7, max UDMA/100, 488397168 sectors: LBA48
ata4.00: ata4: dev 0 multi count 16
ata4.00: applying bridge limits
ata4.00: configured for UDMA/100
scsi 2:0:0:0: Direct-Access ATA Maxtor 7L250R0 BAJ4 PQ: 0 ANSI: 5
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: sda1 < sda5 sda6 sda7 sda8 sda9 >
sd 2:0:0:0: Attached scsi disk sda
scsi 3:0:0:0: Direct-Access ATA Maxtor 7L250R0 BAH4 PQ: 0 ANSI: 5
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: sdb1 < sdb5 sdb6 sdb7 sdb8 sdb9 >
sd 3:0:0:0: Attached scsi disk sdb
pata_pdc2027x 0000:03:03.0: version 0.74-ac5
ACPI: PCI Interrupt 0000:03:03.0[A] -> GSI 19 (level, low) -> IRQ 17
pata_pdc2027x 0000:03:03.0: PLL input clock 16635 kHz
ata5: PATA max UDMA/100 cmd 0xF88417C0 ctl 0xF8841FDA bmdma 0xF8841000
irq 17
ata6: PATA max UDMA/100 cmd 0xF88415C0 ctl 0xF8841DDA bmdma 0xF8841008
irq 17
scsi4 : pata_pdc2027x
ata5.00: ATA-6, max UDMA/100, 390721968 sectors: LBA48
ata5.00: ata5: dev 0 multi count 16
ata5.00: configured for UDMA/100
scsi5 : pata_pdc2027x
ATA: abnormal status 0x8 on port 0xF88415DF
scsi 4:0:0:0: Direct-Access ATA ST3200822A 3.01 PQ: 0 ANSI: 5
SCSI device sdc: 390721968 512-byte hdwr sectors (200050 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sdc: 390721968 512-byte hdwr sectors (200050 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdc: sdc1 < sdc5 sdc6 sdc7 sdc8 sdc9 sdc10 sdc11 >
sd 4:0:0:0: Attached scsi disk sdc

では。