[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[plamo:17571] Re: Plamo3.0でppxpとisdnTA
-
From:nobuhide shimizu
-
Date:Sun, 26 Jan 2003 16:28:33 +0900 (JST)
- Subject: [plamo:17571] Re: Plamo3.0でppxpとisdnTA
- From: nobuhide shimizu <nobushim@xxxxxxxxxxxxxxxx>
- Date: Sun, 26 Jan 2003 16:16:41 +0900
清水です
手もとのv30は plamo3.0につなげるのめんどうなので
KERNEL2.4.18な環境 + PPxP 2001080415(kondaraパッチ)
で試験的にやってみました
# Appletalk devices
....
CONFIG_TUN=m
....
です
回線をきるとルータがおこるのでちょとだけの接続ですけど
前にぼくのいった設定ファイルを採用しました。
On Sun, 26 Jan 2003 15:14:54 +0900
Nishida <VZB14074@nifty.ne.jp> さん wrote:
> Jan 26 13:59:48 [252] OS : PPxP version 200108041
> Jan 26 13:59:48 [252] CONS : <set><LINE></dev/ttyS0>
> Jan 26 13:59:48 [252] CONS : <set><SERIAL.MODEM></nttv30>
> Jan 26 13:59:48 [252] OS : fopen(/etc/ppxp/modem/nttv30) O
> Jan 26 13:59:48 [252] OS : fopen(/etc/ppxp/modem/standard) O
> Jan 26 13:59:48 [252] CONS : <set><DIAL.LIST><354634>
> Jan 26 13:59:48 [252] CONS : <set><DIAL.TYPE><Isdn
> Jan 26 13:59:48 [252] CONS : <set><AUTH.PROTO><PAP><CHAP/MD5><CHAP/MS
> Jan 26 13:59:48 [252] CONS : <set><IP.VJ><yes
> Jan 26 13:59:48 [252] CONS : <set><IP.RESOLV><yes>
> Jan 26 13:59:48 [252] CONS : <set><IP.DNS><202.248.37.74>
> Jan 26 13:59:59 [252] CONS : <connect>
> Jan 26 13:59:59 [252] TIMER: PAUSE
> Jan 26 13:59:59 [252] OS : open(/dev/ttyS0)=
> Jan 26 13:59:59 [252] TIMER: START
> Jan 26 13:59:59 [253] CHAT : write "ATH0E1\r"
> Jan 26 14:00:00 [253] CHAT : ignore until 'AT
> Jan 26 14:00:00 [253] CHAT : read "4\r
> Jan 26 14:00:01 [253] CHAT : dialer: timeout(1500ms
> Jan 26 14:00:02 [253] CHAT : write "ATH0E1\r
> Jan 26 14:00:03 [253] CHAT : ignore until 'AT
> Jan 26 14:00:03 [253] CHAT : read "4\r
> Jan 26 14:00:04 [253] CHAT : dialer: timeout(1500ms)
> Jan 26 14:00:05 [253] CHAT : write "ATH0E1\r
> Jan 26 14:00:06 [253] CHAT : ignore until 'AT'
> Jan 26 14:00:06 [253] CHAT : read "4\r
> Jan 26 14:00:08 [253] CHAT : dialer: timeout(1500ms)
> Jan 26 14:00:09 [252] OS : dialer[253] FAI
> Jan 26 14:00:09 [252] PHASE: Dead =DOWN=> Dea
> Jan 26 14:00:09 [252] CHAT : write "ATH\r"
> Jan 26 14:00:09 [252] OS : close(5)
> Jan 26 14:00:09 [252] TIMER: PAUS
> Jan 26 14:00:09 [252] TIMER: STO
> Jan 26 14:00:29 [252] CONS : <quit
> Jan 26 14:00:29 [252] TIMER: PAUS
> Jan 26 14:00:29 [252] TIMER: STOP
> Jan 26 14:00:29 [252] PHASE: Dead =DOWN=> Dea
> Jan 26 14:00:29 [252] OS : quit
> Jan 26 14:00:29 [252] OS : close(4)
> 以上になり同じ様です?
なんか初期化あたりからこけてません?
手もとのlogですが
Jan 26 15:32:18 [13745] OS : PPxP version 2001080415
Jan 26 15:32:18 [13745] CONS : <set><LINE></dev/ttyS0>
Jan 26 15:32:18 [13745] CONS : <set><SERIAL.MODEM></nttv30>
Jan 26 15:32:18 [13745] OS : fopen(/etc/ppxp/modem/nttv30) OK
Jan 26 15:32:18 [13745] OS : fopen(/etc/ppxp/modem/standard) OK
Jan 26 15:32:18 [13745] CONS : <set><DIAL.LIST><1492>
Jan 26 15:32:18 [13745] CONS : <set><DIAL.TYPE><Isdn>
Jan 26 15:32:18 [13745] CONS : <set><AUTH.PROTO><PAP><CHAP/MD5><CHAP/MS>
Jan 26 15:32:18 [13745] CONS : <set><IP.VJ><no>
Jan 26 15:32:18 [13745] CONS : <set><IP.RESOLV><no>
Jan 26 15:32:18 [13745] CONS : <set><IP.DNS><2XX.2XX.95.XX> #プロバイダのDNS
Jan 26 15:32:23 [13745] CONS : <connect>
Jan 26 15:32:23 [13745] TIMER: PAUSE
Jan 26 15:32:23 [13745] OS : open(/dev/ttyS0)=6
Jan 26 15:32:23 [13745] TIMER: START
Jan 26 15:32:23 [13777] CHAT : write "ATZ\r"
Jan 26 15:32:24 [13777] CHAT : ignore until 'AT'
Jan 26 15:32:24 [13777] CHAT : read "ATZ\r"
Jan 26 15:32:25 [13777] CHAT : read "\r"
Jan 26 15:32:25 [13777] CHAT : read "\n"
Jan 26 15:32:25 [13777] CHAT : found "OK"
Jan 26 15:32:25 [13777] CHAT : write "ATD1492\r"
Jan 26 15:32:26 [13777] CHAT : read "\r"
Jan 26 15:32:26 [13777] CHAT : read "\n"
Jan 26 15:32:26 [13777] CHAT : read "ATD1492\r"
Jan 26 15:32:27 [13777] CHAT : read "\r"
Jan 26 15:32:27 [13777] CHAT : read "\n"
Jan 26 15:32:27 [13777] CHAT : found "CONNECT"
Jan 26 15:32:27 [13745] OS : dialer[13777] SUCCESS
Jan 26 15:32:27 [13745] PHASE: Dead =UP=> Establish
Jan 26 15:32:27 [13745] FSM : LCP: Initial -[Up]-> Closed
Jan 26 15:32:27 [13745] TIMER: START
Jan 26 15:32:27 [13745] TIMER: LCPFSM: install
あと略
設定ファイル1
/etc/ppxp/conf/hogenet.conf
source qdial
set MODE active
set AUTH.PASSWD XXnet0126
set LOG.FILE XXnet0126.log
set LINE /dev/ttyS0
set SERIAL.MODEM /nttv30
set DIAL.LIST 1492
set DIAL.TYPE Isdn
set AUTH.PROTO PAP CHAP/MD5 CHAP/MS
set IP.VJ no
set IP.RESOLV no
set IP.DNS 2XX.2XX.XX.XX
設定ファイル2
/etc/ppxp/modem/nttv30
Name "NTT INSMATE V-30 DSU"
include standard
Initialize "ATZ"
IsdnDial "ATD\p"
HangUp "ATH"
MaxDTESpeed 112500
#スレッドがつながっていいかんじです ^^)!
--------
清水信秀 nobushim@js3.so-net.ne.jp
- Follow-Ups
-
- [plamo:17572] Re: Plamo3.0でppxpとisdnTA, Nishida
- References
-
- [plamo:17564] Re: Plamo3.0でppxpとisdnTAの設定, T.Nikki
- [plamo:17570] Re: Plamo3.0でppxpとisdnTA, Nishida
[検索ページ]
[メール一覧]
Plamo ML 公開システム