[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

[plamo:28150] Re: libata installer(i586 i430VX起動)



   名倉@自己レス です。
 
>   ここで止まってはいけない気分になってしまった。
> 
> > 冨岡です。
> > 
> > From: 名倉昭一 <nagura-s@*********>
> > Subject: [plamo:28147] Re: libata installer
> > Date: Wed, 23 May 2007 15:24:13 +0900
> > 
> > > >   ATA133PCI(SIL680) - (玄人志向)  --- GigaByte GA-8GE800 にて現用品
> > > > 
> > > > を接続してみました。 HDD を実際に接続していないので?の部分は有りますが
> > > > 
> > > > megaraid: 2.20.4.9 (Release Date: Sun Jul 16 12:27:22 EST 2006)
> > > 
> > > > ATA: abnormal status 0x7F on port 0xD407
> > > > 
> > > > こちらは動作しそうな雰囲気があります。
> > > 
> > >   このあたりまでくると実際にインストールして見ないとなんとも?

    i430VX(Shuttle HOT-557 ver1.5) linux-2.6.21.3 どうも動いてくれない感じです。
  linux-2.6.22-rc3が出たようなのでふとChangeLogを眺めていたらlibata回りかなり
  手が入っていたようなのでとりあえずやってみました当たりでした。

root@txp4:/home/snagura# dmesg
[    0.000000] Linux version 2.6.22-rc3-libata2fd (root@txp4) (gcc version 4.1.2) #12 PREEMPT Sun May 27 11:01:56 JST 2007
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
[    0.000000]  BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 0000000006000000 (usable)
[    0.000000]  BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
[    0.000000] 0MB HIGHMEM available.
[    0.000000] 96MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 24576) 0 entries of 256 used
 中略
[  100.093533] Calibrating delay using timer specific routine.. 400.16 BogoMIPS (lpj=200084)
[  100.094253] Mount-cache hash table entries: 512
[  100.095628] CPU: After generic identify, caps: 008001bf 008005bf 00000000 00000000 00000000 00000000 00000000
[  100.095716] CPU: L1 I Cache: 32K (32 bytes/line), D cache 32K (32 bytes/line)
[  100.095847] CPU: After all inits, caps: 0080013f 008005bf 00000000 00000000 00000000 00000000 00000000
[  100.096000] Compat vDSO mapped to ffffe000.
[  100.096148] CPU: AMD-K6tm w/ multimedia extensions stepping 02
[  100.096329] Checking 'hlt' instruction... OK.
[  100.101701] NET: Registered protocol family 16
[  100.133123] PCI: PCI BIOS revision 2.10 entry at 0xfb000, last bus=0
[  100.133260] PCI: Using configuration type 1
[  100.133356] Setting up standard PCI resources
[  100.157349] Linux Plug and Play Support v0.97 (c) Adam Belay
[  100.157640] PnPBIOS: Scanning system for PnP BIOS support...
[  100.158501] PnPBIOS: Found PnP BIOS installation structure at 0xc00fbc80
[  100.158714] PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xbca8, dseg 0xf0000
[  100.166870] PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
[  100.168242] SCSI subsystem initialized
[  100.168772] libata version 2.21 loaded.
[  100.169224] PCI: Probing PCI hardware
[  100.169379] PCI: Probing PCI hardware (bus 00)
[  100.170868] PCI: Firmware left 0000:00:13.0 e100 interrupts enabled, disabling
[  100.175960] PCI: Using IRQ router PIIX/ICH [8086/7000] at 0000:00:07.0
[  100.199424] pnp: the driver 'system' has been registered
[  100.199510] Time: tsc clocksource has been installed.
[  100.200145] pnp: match found with the PnP device '00:07' and the driver 'system'
[  100.200222] pnp: 00:07: iomem range 0xe0000-0xfffff could not be reserved
[  100.200353] pnp: 00:07: iomem range 0x0-0x9ffff could not be reserved
[  100.200474] pnp: 00:07: iomem range 0xfffe0000-0xffffffff could not be reserved
[  100.200674] pnp: 00:07: iomem range 0x100000-0x5ffffff could not be reserved
[  100.204687] NET: Registered protocol family 2
[  100.213903] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
[  100.214688] TCP established hash table entries: 4096 (order: 3, 32768 bytes)
[  100.215378] TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
[  100.215821] TCP: Hash tables configured (established 4096 bind 4096)
[  100.215936] TCP reno registered
[  100.222215] audit: initializing netlink socket (disabled)
[  100.222452] audit(1180264277.175:1): initialized
[  100.223304] Total HugeTLB memory allocated, 0
[  100.225127] io scheduler noop registered
[  100.225345] io scheduler cfq registered (default)
[  100.225532] Limiting direct PCI/PCI transfers.
[  100.225649] Activating ISA DMA hang workarounds.
[  100.225803] Boot video device is 0000:00:12.0
[  100.227120] isapnp: Scanning for PnP cards...
[  100.584439] isapnp: No Plug & Play device found
[  101.061148] Real Time Clock Driver v1.12ac
[  101.062736] eepro100.c:v1.09j-t 9/29/99 Donald Becker
[  101.062757] eepro100.c: $Revision: 1.36 $ 2000/11/17 Modified by Andrey V. Savochkin <saw@xxxxxxxxxxxxx> and others
[  101.063097] PCI: setting IRQ 11 as level-triggered
[  101.063121] PCI: Found IRQ 11 for device 0000:00:13.0
[  101.074382] eth0: 0000:00:13.0, 00:A0:C9:8C:2C:5F, IRQ 11.
[  101.074730]   Receiver lock-up bug exists -- enabling work-around.
[  101.074841]   Board assembly 678400-001, Physical connectors present: RJ45
[  101.074945]   Primary interface chip i82555 PHY #1.
[  101.075398]   General self-test: passed.
[  101.075410]   Serial sub-system self-test: passed.
[  101.075424]   Internal registers self-test: passed.
[  101.075437]   ROM checksum self-test: passed (0x49caa8d6).
[  101.075802]   Receiver lock-up workaround activated.
[  101.085008] ata_piix 0000:00:07.1: version 2.11
[  101.086633] scsi0 : ata_piix
[  101.087628] scsi1 : ata_piix
[  101.088396] ata1: PATA max MWDMA2 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001f000 irq 14
[  101.088586] ata2: PATA max MWDMA2 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001f008 irq 15
[  101.245475] ata1.00: ATA-0: WDC AC2850F, 28.25E40, max MWDMA1
[  101.245608] ata1.00: 1667232 sectors, multi 16: LBA
[  101.250473] ata1.00: configured for MWDMA1
[  101.552541] ata2.00: ATAPI, max MWDMA2, CDB intr
[  101.703518] ata2.00: configured for MWDMA2
[  101.704862] scsi 0:0:0:0: Direct-Access     ATA      WDC AC2850F      28.2 PQ: 0 ANSI: 5
[  101.706632] sd 0:0:0:0: [sda] 1667232 512-byte hardware sectors (854 MB)
[  101.706903] sd 0:0:0:0: [sda] Write Protect is off
[  101.707019] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  101.707278] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  101.707997] sd 0:0:0:0: [sda] 1667232 512-byte hardware sectors (854 MB)
[  101.708310] sd 0:0:0:0: [sda] Write Protect is off
[  101.708427] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  101.708620] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[  101.708798]  sda: sda1 sda2
[  101.725842] sd 0:0:0:0: [sda] Attached SCSI disk
[  101.727495] scsi 1:0:0:0: CD-ROM            E-IDE    CD-ROM 40X/AKU   U30  PQ: 0 ANSI: 5
[  101.733216] sr0: scsi3-mmc drive: 0x/40x xa/form2 cdda tray
[  101.733365] Uniform CD-ROM driver Revision: 3.20
[  101.734215] sr 1:0:0:0: Attached scsi CD-ROM sr0
[  101.736227] pnp: the driver 'pata_isapnp' has been registered
[  101.741164] pnp: the driver 'i8042 kbd' has been registered
[  101.741596] pnp: match found with the PnP device '00:04' and the driver 'i8042 kbd'
[  101.741695] pnp: the driver 'i8042 aux' has been registered
[  101.742261] PNP: PS/2 Controller [PNP0303] at 0x60,0x64 irq 1
[  101.742407] PNP: PS/2 controller doesn't have AUX irq; using default 12
[  101.994341] serio: i8042 KBD port at 0x60,0x64 irq 1
[  101.995893] mice: PS/2 mouse device common for all mice
   中略
[  114.637521] Adding 125488k swap on /dev/sda1.  Priority:-1 extents:1 across:125488k
[  172.223176] ata1.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x2 frozen
[  172.223400] ata1.00: cmd ca/00:70:68:df:10/00:00:00:00:00/e0 tag 0 cdb 0x0 data 57344 out
[  172.223420]          res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
[  172.223613] ata1: soft resetting port
[  172.404190] ata1.00: configured for MWDMA1
[  172.404330] ata1: EH complete
[  172.464699] sd 0:0:0:0: [sda] 1667232 512-byte hardware sectors (854 MB)
[  172.544475] sd 0:0:0:0: [sda] Write Protect is off
[  172.544525] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[  172.558203] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA





Follow-Ups
[plamo:28151] Re: libata installer (i586i430VX起動), Mikio Tomioka
[plamo:28153] Re: libata installer(i486 um8810p CMD640起動), 名倉昭一
References
[plamo:28144] Re: libata installer, 名倉昭一
[plamo:28146] Re: libata installer, Mikio Tomioka
[plamo:28147] Re: libata installer, 名倉昭一
[plamo:28148] Re: libata installer, Mikio Tomioka
[plamo:28149] Re: libata installer(i486 SiS496起動), 名倉昭一

[検索ページ] [メール一覧]
Plamo ML 公開システム