[plamo:19204] dhcpそのまた続き

[bpbcy700]

ひらたです。

名倉さん。以下のようです。
参考になればよいのですが。

--------------------------------------------
（起動直後）
lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:50 errors:0 dropped:0 overruns:0 frame:0
          TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:3500 (3.4 Kb)  TX bytes:3500 (3.4 Kb)
--------------------------------------------
（起動直後）
tulip-diag.c:v2.17 5/6/2003 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21140 Tulip adapter at 0xec00.
Digital DS21140 Tulip chip registers at 0xec00:
 0x00: ffa05000 ffffffff ffffffff 07f80000 07f80200 fc000102 32040200 fffe0000
 0x40: e0000000 fff583ff ffffffff fffe0000 ffffff40 ffffffff 1c09fdc0 fffffec8
 Port selection is MII, full-duplex.
 Transmit stopped, Receive stopped.
  The Rx process state is 'Stopped'.
  The Tx process state is 'Stopped'.
  The transmit threshold is 128.
EEPROM 64 words, 6 address bits.
PCI Subsystem IDs, vendor 8212, device 0091.
CardBus Information Structure at offset 00000000.
Ethernet MAC Station Address xx:xx:xx:xx:xx:xx.
EEPROM transceiver/media description table.
Leaf node at offset 30, default media type 0800 (Autosense).
 CSR12 direction setting bits 0x80.
 4 transceiver description blocks:
  21140 Non-MII transceiver for media 0 (10baseT).
   CSR12 control port setting 00, command 00 0x1d.
   Media detection by looking for a 1 on bit 6 of the CSR12 control port.
  21140 Non-MII transceiver for media 3 (100baseTx).
   CSR12 control port setting 00, command 00 0x8d.
   Media detection by looking for a 0 on bit 6 of the CSR12 control port.
  21140 Non-MII transceiver for media 4 (10baseT-Full Duplex).
   CSR12 control port setting 00, command 00 0x1b.
   Media detection by looking for a 1 on bit 5 of the CSR12 control port.
  21140 Non-MII transceiver for media 5 (100baseTx Full Duplex).
   CSR12 control port setting 00, command 00 0x8b.
   Media detection by looking for a 0 on bit 5 of the CSR12 control port.
 MII PHY found at address 1, status 0x782d.
 MII PHY #1 transceiver registers:
   1000 782d 0181 b800 05e1 45e1 0003 0000
   0000 0000 0000 0000 0000 0000 0000 0000
   0640 8018 6800 0000 0000 0000 0000 0000
   0000 0000 0000 0000 0000 0000 0000 0000.
---------------------------------------------
（ifconfig eth0 upののち）
eth0      Link encap:Ethernet  HWaddr xx:xx:xx:xx:xx:xx  
          UP BROADCAST RUNNING  MTU:1500  Metric:1
          RX packets:0 errors:4 dropped:0 overruns:0 frame:0
          TX packets:2 errors:2 dropped:0 overruns:0 carrier:4
          collisions:0 txqueuelen:100 
          RX bytes:0 (0.0 b)  TX bytes:1180 (1.1 Kb)
          Interrupt:11 Base address:0x1f80 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:50 errors:0 dropped:0 overruns:0 frame:0
          TX packets:50 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:3500 (3.4 Kb)  TX bytes:3500 (3.4 Kb)
----------------------------------------------------------
（上に同じ）
tulip-diag.c:v2.17 5/6/2003 Donald Becker (becker@scyld.com)
 http://www.scyld.com/diag/index.html
Index #1: Found a Digital DS21140 Tulip adapter at 0xec00.
 * A potential Tulip chip has been found, but it appears to be active.
 * Either shutdown the network, or use the '-f' flag to see all values.
Digital DS21140 Tulip chip registers at 0xec00:
 0x00: ffa05000 ffffffff ffffffff 07f80000 07f80200 fc660000 32042202 ffffebef
 Port selection is MII, full-duplex.
 Transmit started, Receive started.
  The Rx process state is 'Waiting for packets'.
  The Tx process state is 'Idle'.
  The transmit threshold is 128.